Letter from Hong Kong (24-14): Another Longest Day, Part I
Cheaptubeaudio has had a long history of advocating reasonably priced but excellent tube gears, particularly Singled-Ended Triodes. This Blog however covers a lot more than SET, and is not exclusively tube-related. Cheaptubeaudio prioritizes coverage of unusual and rare gears, particularly vintage ones, on which little info can be found on the internet.
30 April, 2024
Take One Audio 派美 CS Port Viva Esturo Kuzma
Letter from Hong Kong (24-14): Another Longest Day, Part I
29 April, 2024
Faith, Conviction, Cheap Amps
24 April, 2024
Douk H7 Pro Nobsound
- A Word on Cables I basically used my regular cables (for interconnects, like Belden 8451), no different than when I'm using my tube amps. But, initially, for convenience, I recruited my Canare 4S10F 4-conductor bi-wire loudspeaker cable (normally hooked up to our keyboard and Sansui loudspeakers) just because I didn't want to upend my tube amps. But during the run-in, the sound proved to be too forward and a little sharp, so I reluctantly reverted back to my somewhat slower and darker (but more depth) "Belden 1309" and, voila! that smoothed out the sound significantly and they stayed.
- As Integrated Amp This means, in my case, DAC direct in, using the unit's volume control. From my listening, this is an amp with a passive volume control (no additional gain in "preamp stage"). Sound is decent and transparent, with good air, rhythm and pace. The initial bit of tightness and treble grain smoothed out with run-in. I right now have on hand 2 DACs, and they are very different, and the H7 Pro effortlessly shows the difference. Very good!
- With Tube Preamp Used as an amp, the volume is maxed out. Although each Preamp brings its own color, across the board a (Tube) Preamp brings additional benefits: more tonal sheen, better control and greater dynamics. Addition of preamp also makes the images a little more textured and clearer in outline. Of course, tubes make the soundstage larger and airier. The transparency of the H7 Pro means the differences between the preamps are very apparent: the 6J4/6P3P is slower in transient and less focused, which I preferred during run-in, but not afterwards; the ETA 6N3 SRPP (with JAN GE 5670) is very focused and airy but it developed problems (again); the tube-buffered op-amp based Douk T8 Pro (with 6CG7) proves to be a good match, well-tempered and with good transient speed. As for the Douk E6 , it imparts the most air and the largest soundstage.
- XLO Facilities I haven't tested this yet, as I don't have any XLR cables or adaptors here in SZ. But next time I go to HK I shall bring both the H7 Pro and T8 Pro with me to test out the XLR connection. Not only that, I could challenge the H7 Pro with the B&W Matrix 801 Mk II - a tall one indeed.
- vs Aiyima A08 Pro I don't have the Aiyima anymore. From my memory, I'd reckon the H7 Pro is a little smoother and more refined. But why rely on faulty memory? I shall get this to ELO, who is still using the Aiyima, for a fair comparison. Also, his Dynaudio Crafft is much harder to drive, so that's a good challenge. And, he has the larger power supply (36V). Whether he agrees with my assessment or not, I shall be happy with a large slice of truth!
Below are several albums played during this evaluation. Big complex works well rendered!
23 April, 2024
UMI 2 Clarity Plus S2
Letter from Hong Kong (24-13): ELO on UMI 2 Clarity Plus S2, Part II
It's been a few weeks since I received the new UMI 2 and I have been using it everyday. Some may wonder why I am so enthusiastic about this product. I hereby declare that I have no personal interest in this brand and I bought my own UMI unit. I do not know Engineer Li (the chief designer) nor had any contact with him although I would love to meet him!
I have been praising this little transformer for so long (since Mk I) it's possible some readers may wonder whether I have overexaggerated the effects. Well, thanks to Icefox, who had recently organized a group buy, 3 of my Hifi friends who trust my ears also took the plunge.
Initial Feedbacks from my Hifi Friends
Kwong He has been my long term Hifi buddy since the 90s. We have been inspiring each other and often recommend gadgets and gear to each other. I took his advice on the "Studer" cables and the popular little Bluetooth device H9A. The "Studer" Cables has now become indispensable in my system. While I had recommended to him quite a few items in his current system:Audionet, JMR, Holo Spring, Rayaudio and now the UMI!
He was so excited that he called me on two consecutive nights to tell me how amazing this unit is! At the beginning, the sound of UMI 2 Clarity Plus was not appetizing to him at all! But the second night, with a little play time under the belt, the unit transformed itself and then went from strength to strength! Here's his view:
"...the high end extension seems limitless. With the UMI, the supertweeter flourished. The music is now extended beyond the walls and the soundstage had been pushed back 3 feet to create a holographic soundstage. The decay of instrument seems to last forever, like the half-life of Uranium, LOL! The loudspeakers just disappeared!
...Background becomes darker, resulting in heaps of low-level details emerging from the depths. Bass extension improves and more bass details show up. Playing Chinese Guqin is such a treat and I'm stunned by the endless reverbs of decaying notes washing over each other. Imagine rain falling on a pond and creating ripples which intersect with each other!
...Vocals is natural with no edges nor any digital glare. I'm drawn into the sea of music and have no choice but to isten to song after song. Even familar songs which I have listened to hundreds of times sound like brand new songs or recordings!
...In conclusion, UMI is THE most important upgrade in my system. The word "improve" is not enough; "transform" is more like it!..."
Needless to say, he immediately placed an order for additional one!!
"7" Another friend who was perhaps a bit skeptical initially about my overly enthusiastic recommendation (remember that I almost lost a friend over hard persuasion) and procrastinated a bit but finally joined the group buy. Needless to say, we have another happy customer, and here's what he wrote:
"...好多謝一位音響師兄前輩朋友ELO兄介紹我使用,起初都半信半疑,引不起即時購買嘅意欲,又相隔一段時間,ELO師兄告知攪了一個團購計劃,抱住信ELO師兄心態去購買,貨到時ELO師還親自帶給我,正值下午時份沒時間測試,當晚工作結束,打開包裝插進系統,一著機,這還是我的系統嗎?這音效從未出現在我的音樂室,真是太豐富太精彩,多了從來未聽過的音樂細節,這次真是買對了,也即時覺得這次花費,物有所值,完全超出金錢上的性價比,真的沒有介紹錯,我還打算多購入一台去再次提升糸统,這次花錢來得出的效果十分顯著明顯有效,感謝ELO兄推介,也希望多啲同好受惠..."(Translation: Many thanks to my HiFi friend ELO who had introduced the UMI to me. At first I was skeptical with the UMI and did not have the urge to try it out. After a few months has passed, ELO told me that there's a group buy, so I thought I may give that a try based on his recommendation. ELO delivered the UMI 2 to me in person! I waited till the night after work and unwrapped the unit and hooked it up immediately. At once , I asked myself if this is the same system I have been listening to everyday? The extent of impact and improvement brought by UMI2 has not been experienced in my music room previously and it's simply amazing. I heard so much more details in music which were not picked up before. I think I made a right decision and also think the money spent is well worth it. The PQR value surpasses any products I had bought previously. That was a heck of a recommendation and I am planning to buy another unit, hoping to elevate further the performance, which is so pronounced and immediate. Thanks ELO for his persistent recommendation, and hope more hifi lovers can benefit from this unit.)
Also, needless to say, he immediately placed an order for additional one!!
Well, things has progressed unexpectedly in a good way. I had bought him some tourmaline chips and a big piece of black tourmaline for him to DIY a gorund box. Today, he bought a wooden box and use a cheapo wire to connect it to the back of his router. He heard a difference immediately and can hear more nuances of singing skills of Sandy Lam which makes her famous! So his setup has improved due to various upgrade! Good to know! I give some credit to his DIY Ground box, UMI1 and "Studer" cable, LOL!
My impressions
By now, you must be curious on my own experience with the UMI 2 Clarity Plus S2 and how does that compare to my UMI 1. After I plugged in the UMI 2 and start listening to it, I lent my UMI 1 to Dr. Lo so I still haven't had the chance to directly A/B. Strangely, Dr. Lo is the only person among my friends who has experienced a setback in musical experience. I don't know what went wrong and scratch my head. He's giving me the chance to go over to his place; maybe I can try to find out why and that's the fun of playing with Hifi, haha.
My initial feeling is, if broken down into hifi parameters, all the good things that UMI 1 has, UMI 2 Clarity Plus has them too, and perhaps I do not feel any significant improvement. However, as a whole, there is an improvement in overall musical experience. The sound has gained refinement and has become more organic, smoother, more natural and musical. At first, I felt that there may be a slight loss in detail when compared to UMI 1. But the more I listen, the more I do not feel that way. In fact, the details are there but not as flashy. The music presentation has become more holistic - I would say overall a 10 to 15% increase in quality of UMI 2 Clarity Plus over UMI 1 (since the starting point of UMI 1 is quite high already)
21 April, 2024
2024 Shanghai AV Show
This Weekend is the Shanghai AV Show. There may be more than one audio shows in Shanghai but this one is pretty big and it looks like all major players are there. This report is by the Weixin Site 视听至前线. Declaration: all pics from them (click to enlarge). Those with WX can watch it on their Cellphones. Those without can peruse the links below:
It hardly matters if you don't know Chinese. The pictures speak for themselves, and you may find things to linger on. For me, it's just like a somewhat bigger Shenzhen Show. American readers will find many brands they don't know about. Enjoy.
18 April, 2024
MouthDancing Cafe 嘴舞咖啡
Click pics to enlarge. The top pic is placed only because this is an audio blog after all. Sun Audio 2A3 amp (with good old-stock tubes) driving Proac Tablette (a later edition). Rega TT. To the right, the “Chemistry Lab Apparatus" flanking Leon is what is used to make Ice-Drip Coffee!
Letter from Shenzhen (24-5): MouthDancing Cafe 嘴舞咖啡
Note: A Chinese expose shall be added soon. Come back soon.
Serendipity! Some months ago ELO mentioned that he knows this interesting fellow from Hong Kong who has opened a Boutique Cafe in Longgang district (borough), where I live. After some to and fro, I found out it is located on a street which I know very well because I have lunch once in a while at several of the cheap eateries around there! I have witnessed first hand the transformation of this very street - previously it was a sleepy neighborhood street with humble eateries but over the last years swanker Cafes kept popping up.
A bit later, Jim made a (for me) highly unusual Hand-Drip Coffee and it was wonderful to savor the taste change as it went from hot to warm. This is a masterwork. Jim has his beans roasted to his specifications.
11 April, 2024
Beydas Douk T8 Pro GE 5670 WE 274B 350B 80
Letter from Shenzhen (24-4): Listening Notes
Douk T8 Pro Equalizing Preamp, Part I, Part III (on XLR use)
Lately, though still based in SZ (hint: not for long), I have had the opportunity to conduct some listening sessions in HK, much of it reported in recent articles. I had been busy writing those up as well as with private matters, so it's now time to update you on what I've been up to around here in SZ. It's basically tinkering with what I have here, AND with some tube rolling. Not just any tube, but some old stock Western Electric tubes brought over from HK; with WE, it's always a transformative experience! But I shall start with humbler stuff.
- Whether for initial run-in or after long disuse, (re-)running them in is a must.
- 15 ohm This version is really quite lean in the bass but easier to manage in a way. The lack of bass heft (at least 10db less than the 11 ohm) ensures good transient response and clarity in the midband and ease of partnering. When properly matched, sound is very lucid but the lightness in the bass shall not suit all, though I find its bass pitch and definition highly satisfactory.
- 11 ohm This version is much more bassy, but at the cost of some loss of definition in the lower midrange and bass. Therefore, more care has to be taken with partnering equipment. Overly rich-sounding gear or "tubey" stuff may not do so well, resulting in a sound that is rolled off in the treble and smeared lower down (reader Collins has complained of this, but I don't know his associated equipment). Transistor or T- and D- amps likely do better. What one needs is better speed and definition in the amplification. E.g. my Douk T8 Pro Preamp suits it more than my others because of its superior transient speed (see below). The Beydas 11 ohm also respond well to my leaner sounding BRZ FU50 (when used with a suitable rectifier). When optimized, sound is perhaps a little closer to the real LS3/5As than the "15 ohm".
- Douk T8 Pro This Preamp has continuously surprised me by its versatility. Mind you, this is the only Preamp in my active use arsenal here that is not pure tube, being a tube buffered op-amp design. But why not? The very expensive MBL 6010 (which is garbage imho) is just an opamp preamp that sells for the price of a car! But to compare the Douk with MBL is to tarnish the Douk, which has much more flexibility and sheer life to it! Transient Speed As mentioned before, its prowess here saves the day in many a situation. It serves the 11 ohm Beydas (which can be darkish) well. With tube gear, sometimes things gets slowed down and, when overly so, is not desirable. A faster transient preamp can make the difference. That said, faster transients can exact a cost. Things can get breathless, which is NOT the case here, thank God. Perhaps sometimes one wishes for a trifle more lingering, a little more harmonics, but one adapts. Suffice to say, it proves very useful here in SZ. XLR Use Finally, one day I brought it over to HK (with stock small wall wart). I connected it (with Gotham GAC-3 XLR cables) between the XLR output of my Marantz 94 Limited DAC and an early iteration of Bryston 4B amp, driving the B&W Matrix 801 Mk II. Sound was very good. At low volume, I swear it was even more detailed than many of my hifi preamps, the hybrid ARC SP-11 included. But, ultimately, at higher levels, it did not prove to be better at matching with the Bryston than my RCA output only tube preamps, be them MFA Magus or even Counterpoint SA3000. So, not a success yet. Capacitor Mods There being so many, I have to contact Douk on which ones are the most important. But this is in the agenda.
- ETA 6N3 SRPP Preamp (pic above with 5670 tubes) As mentioned previously (in Part III), the Preamp developed problems in RCA Contact as well as Volume Pot. RCA Terminal Woes I thought I rectified this after re-soldering but it irritatingly still periodically failed (even sometimes as I write) to make contact with my GAC-2 (brought over from HK) which has the "Canare" plugs I bought from Apliu St (and SZ 万商) ages ago (and I never had problems with my gear in HK). These plugs manifestly don't agree with the ETA's RCA terminals, which look of "reasonable quality" outwardly. Some wiggling is usually required to enforce contact. But I'm thinking of changing them out. Incidentally, my cheap Rean plugs don't have this problem. Volume Pot I finally dug out the spare tiny cheap Volume Pot that came with one of the kits. It's 100K instead of the ETA stock 50K. What the hell, I just did the surgery, not too difficult. Voila! The pot functions well (for now) and I could use it at all positions, even with my BRZ 6L6 Amp! GE JAN 5670 Finally, I yielded to temptation and bought a few from Taobao (cheaper than HK or US). These were from '86, last of the Mohican's, but came matched in sections (as JAN tubes are wont to be). Of course, I'd have preferred WE396A /2C51 but those now command very high prices. At first, I was non-plussed by the sound of the GE 5670 - controlled and finely textured but overly reticent. For quite a while, I reverted back to my Douk T8 Pro (with 6CG7) for more oomph factor. BUT, guess what? The 5670 gradually came to life, becoming livelier and more dynamic, and now can serve in most situations, though some may still prefer the more gun-ho nature of the Russian 6N3. This tube takes quite a while to run-in! I have more to say on this tube but it shall be in another article devoted to tubes.
- WE 274B Of course, this immediately transformed the sound of my tube-rectified APPLause 300B amp and BRZ FU-50 amp. The sheen, rhythmic subtlety and ease of delivery is immediately evident. Mind you, many audiophiles, including many I know, are arrested in the tonality stage and judge everything by a few vocal recordings (kinda like HiFi News Kessler) and these people often fail to grasp what makes WE great. Problem is, should I run the 274B for >10 hours a day? I cringe...Mind you, many modern tubes tout themselves for guaranteed 3000 hours but, man, this is less than a year for me! I know, WE tubes can last forever, but we still want to use them when everything is optimal, not wasted.
- APPLause 300B Putting aside the 274B, this amp runs well on my Chatham 5R4WGY and Philips JAN 5R4WGB and National Union old 5U4G. The hotter the weather, perhaps the less suitable this amp. It just occurs to me to swap out the Linlai 300B and exchange with my older Russian and Chinese 300B's in HK. Soon. No, I'm not going to bring my WE 300Bs over to SZ, as I'm in Retreat Mode. I tried my Tung Sol 80 (ST engraved) too: it works despite arcing on turn on; and current drops to 130 mA for both channels combined. Fine with me, but the 80 works better below...
- BRZ FU-50 This amp I use the most, because it's performs well enough (less power than 300B) and does not heat up the room so much that it can be used in the summer. My Tung Sol 80 (ST) works very well in this amp (with adaptor). No arcing and it complements the slightly leaner sonority of the amp with its richness and, yes, soul. The 80 is a very fine tube, being descendent of the venerable WE 274A. It's a little darker, slower in transient and almost as subtle as the WE 274B; through its DNA has inherited a bit of the old-world magic, that is soul. The ST 80 is still an affordable tube, significantly cheaper than Globe ones, and you should try it! So! The FU-50 amp with the 80 rectifier is my main amp.
- BRZ 6L6 SE Amp Well, SS rectified, so the WE 274B and 80 are out of the equation. In previous installments, I detailed the tube rolling (some with adaptors) I had done for the 6N2 and had mostly used it with my 6SN7/L7. WE 350B Then, about 2 weeks ago, I brought back from HK a pair of the WE 350Bs. Initially, replacing the Executone (Sylvania) 6L6GCs, I was shocked by how lackluster the sound was. I let them run for quite a while and still the sound lacked dynamics. Now, as the 350B is not quite a 6L6 type, I thought it likely needs more drive, which the 6SN7/L7 were not providing (less gain than the stock 6N2) . This is not just a matter of gain (which the preamp can make up), it's the swing required to drive the tube. Adaptor Woes So I sought to drive the 350Bs with my 12AX7 with the adaptor. NO Sound! After some tube swapping, it was clear that the adaptor now works only with 6V filament tubes (like 6CG7), and not with 12V filament tubes. For sure, a solder joint inside has gone bad. Desperate, I put back the stock 6N2 (Beijing). Voila! Sound was much improved! In fact, I was floored by how good the sound was! Yes, even with the lowly Chinese 6N2, surely not the best driver tube, the WE 350B showcased its famous qualities. Like the WE 274B and 300B, it lacks nothing: Rhythmic sophistication, tonal opulence, clarity, wide bandwidth and the most natural of dynamics. Simply put, I heard the famous WE sound, and this in an amp that costs less than 1/20th of the pair of tubes! This also attests to the reasonable quality of the output transformers, no mean feat in such a cheap amp. There are things to watch out for though. The 350B, here run in Ultralinear, surely draws more current than 6L6GC or EL34, though probably less than KT66, which I don't advise in this amp. The Power Transformer is a little hotter than usual, but not excessively so. So let's see how it fares in the long run. vs BRZ FU-50 and APPLause 300B Now, with the WE 350B on board, this little amp has become my Special Reference Amp here in SZ, its sound quality surpassing the BRZ FU-50 and APPLause 300B without WE 274B. Even with the 274B, the FU-50 and APPLause cannot completely overtake the 350B amp. This is an amazing development, which I had not foreseen. Now, you must read me carefully and I stress, this result can only be achieved with old-stock WE 350B, nothing else. Volume Pot Defect Well, small hiccups happen often with these cheap machines, no? Here again, it's the volume pot (remember my ETA Preamp, APPLause Amp), which I basically don't use actively, because I max it out and use a Preamp in front. However, when I change preamps, I turn the volume to zero. During one such swap, I heard crackling noise in the middle of the range, and it was repeatable - sure enough, the volume pot has turned bad. It doesn't affect how I use it, but the problem has to be rectified at some point. So, if you use it as an integrated, this may ruin it for you.
01 April, 2024
UMI 2 Clarity Plus S2 version 优美 1:1 Isolation Transformer
Letter from Hong Kong (24-12): ELO on UMI 2 (latest Clarity Plus S2 version), Part I
ElO's Review of UMI 2 Clarity Plus, Part II published
Editor: I have written several articles on the slightly older UMI 2 (for a start, see here and here) but it's great to have now the initial evaluation of the latest v2 by ELO! See sections below for the subtle functional, cosmetics and sonic differences between my v2 and his latest v2).
The long awaited UMI v2 (UMI 2) has finally arrived thanks to icefox for organising the group buy! As I mentioned previously, 4 for me and my friends.
Round 1, Chez Mila's
We had arranged pickup at his freind Mila's shop on Tai Ping Road in Sheung Wan, a quaint street with a unique vibe rarely found elsewhere in HK. I used to visit the area for taking street photos or just hanging around. His shop has a back alley which is arguably the cleanest in HK, just perfect for food and wine gathering with friends!
Me and Jo arrived at the shop around 7 pm to pickup our orders, one each for me and Jo, another for Kwong and the last one for another Hifi friend "Seven" who is now using Infinity Renaissance 90 and Lab12 preamp, and I can't wait to hear his system with UMI 2 in the mix.
Mila's place is actually a hair salon with a small but dedicated space that houses a very unique system. When I first look at his setup, I know he is a seasoned veteran as his equipment are definitely far from main stream, kinda like mine even if our systems are very different in direction of preference. After a short conversation with him, I immediately realised that he is more of a music lover than an "Effects Chaser", and we do share the same belief on how a good piece of music should sound like. Afterall, it's music that we are chasing, not effects!
Before I describe the sound from his setup, let me make a run down of his interesting setup! I categorize him as like me, an " Itchy Ass" kinda guy, meaning we don't want to be tied up by the mainstream stuff and instead like to find our own way. Thinking of my system, I suddenly realised that it comprises products made in Denmark, Sweden, Switzerland, UK, Japan, Mainland China, France, Germany and Canada! In it I used 6 earth boxes to kill background noise in order to achieve a low noise floor. Diversity and open-mindedness and know-how is what a music/hifi lover should have in mind all the time.
R, Cyrus One atop EAR Phono Amp (chrome)Setup Mila uses Bluetooth to stream Tidal music. He is also a user of H10U (variously branded as Kyoeon 友昂, You Sheng Heng 友聲恆 or Wenliang), the el-cheapo little BT device which Kwong introduced to me and which I had written about in an early post [Editor: Before the H10U, ELO used the H-9A and reported on it. I then got the H-9A courtesy of ELO, written up here; still has it in SZ. It should be noted that in ELO's reports, he preferred both the H9A and H10U to the popular and well-reviewed iFi Zen Blue - this is illustration of this Blog's independence from commercial influence!]. I believe it has become a popular cheap yet effective musical device! He then uses multiple Reisong signal transformers and Douk E6 as preamp (his unit does not have any tube ringing as reported by DJ!) Then through a generic red/black wire to a MCM Reverse/Inverse RIAA device that converts the analog output of BT into an RIAA signal, which is then sent to his newly acquired "EAR 88P" (Chinese clone)! Then the "EAR" converts the RIAA signal back into analog signal and send the signal to the early version of Cyrus One Integrated Amp driving two pairs of Stirling 3/5A, stacked!! What an interesting setup and I noticed he must have followed this Blog. M told me originally the Reverse RIAA unit was acquired to run in the EAR phono, but it turned out the system sound had improved to a point that it has now become a pivotal piece in his setup. What a beautiful accident! Sound from streaming Tidal has surpassed his Turntable and he told me he mainly streams music through Tidal now.
Unboxing the UMI2 was such a pleasure. It came in a box only slightly larger than the unit, with a snug and tight fit. The unit itself is sturdy, with near-perfect metal works, like my UMI 1, not surprisingly.
Before UMI 2 We had an initial listening session with Mila's standard setup before moving on to implant the UMI2 and my Studer cable into the system. Overall sound was musical, and was already quite good. His liking is towards a meatier midrange and I can understand since stacked (15 ohm) 3/5As were used!! The stacked Stirling's seemed to add some heft in the lower octaves [Editor: interesting as a single pair of the Stirling 15 ohm tends to be lean in the bass; perhaps this is the result of stacked pair!]. The overall sound was very enjoyable and analog, without too many Hifi artefacts. His setup, with a listening distance of only 6 or 7 feet, tends to be more upfront and in your face compared to mine (which is like seated at the 8th row while his is 3rd row).
One thing that I really want to comment on: the whole system does not make me feel the shortfall of using a mass market Bluetooth receiver in streaming music. Back some time ago, for a while I had used BT to stream music; even now, I still use the BT that is built in to my Aiyima A08 Pro to stream TV and Youtube videos. They sound really good but ultimately fall behind the my proper setup using WEA. With the addition of UMI 1, I began to feel the gap widening between the two. Having said that, I'm still enjoying streaming Youtube music videos thru Bluetooth .
+ UMI 2 Then we inserted the UMI 2 between the EAR and Cyrus. Upon turning up the volume, the sound had taken a change for the better. The bass dug deeper and with better definition, and imaging had tidied up without taking away the musicality. Musicians seemed to have drunk some Red Bull's, suddenly more alert and played at their highest level. Shades and Colours were fantastic, the flow smoother, more toned up and conditioned in body, all to my liking. Also, reverbs and decays were portrayed nicely in the background. Very enjoyable indeed given the listening in limited space (around 100 sq. ft I would guess).
Mila told me that his experience this night was very different from what he had heard from the loaner UMI 2 that DJ had earlier left to his HiFi buddies in HK to audition. M would have joined the group buy based on what he had heard on this night, which in his opinion was significantly better than his previous encounter. This begs the question: Perhaps this batch of transformer is better in quality? I'd think, like many smaller brands, the designer feverishly chases after improvements, so any upgrades will be implemented into the next batch without changing the version number. Therefore, it is no surprise that the most current batch's sound is superior to the previous batches! [Editor: Because of this I spoke to Engineer Li of UMI and clarified the differences; see below]
Detour: "Studer" Cable Then we added the "Studer" cable into the mix, we experienced a slight softening and increased smoothness in the music, For me the "Studer" may be a perfect match to take away some kick and coolness from my Aiyima A8 Pro and UMI 1, but on his setup, which is quite rich in body, the sound, though still very nice, turned in a slightly different direction! I tend to think that "Studer" cables is more suitable for cooler systems.
I think Mila's system definitely benefits by inserting the UMI 2 into the lineup. I think it integrates musicality and hifi values seamlessly! I'd also recommend trying out an earth box, as the background can become darker and more valuable music information can be retrieved!
Next time, I will bring my Wattson WEA and my Entreq Earth box over to try - should be quite interesting! BTW, some days later I went again with my family for a stroll around the Tai Ping St and Hollywood Rd area and there's a shop selling a vast array of precious stones and crystals across the street from Mila's salon. I bought another pack of tourmaline and a piece of black tourmaline for Jo for his DIY earth box project.
Round 2, Chez Moi
Recently, for no particular reason, the sound suddenly suffered a setback, becoming less engaging and the soundstage seemed to have shrunken slightly. Except for switching cables for comparisons I had not altered anything. DJ reminded me that he had similar experience before and that it will go away eventually. I had my fingers crossed but, sure enough, days later the previous musical sound returned in full and now I'm back in Enjoy mode, yeah!
I have now replaced the UMI 1 with the UMI 2 in my system and will let it run-in for a week or so before I would switch it back to my UMI 1. DJ had said that the sound traits should be more similar than dissimilar, which is also my initial feeling, though I think the v2 has a slight edge. I am curious about the actual differences when UMI 2 is fully burnt in. It is already amazing!
- Latest Version is Clarity Plus S2 This is silkscreened on the casing (see above pic; the previous v2 does not have this). ALL of ELO's comments above are based on this latest version! Mine is the older version without such words.
- Trannies (core materials etc) are the same.
- Circuit Board is the same, but re-purposed for the different Ergonomics [Editor: Wiring is certainly different and simplified].
- No more 300/600 ohm Choice. Only 1:1 600 ohm now. [Editor: IMHO, this is a good move as I had found the 300 ohm to be not much of a higher gain and pretty superfluous. The simpler the better].
- Phase Switch remains the same. [Editor: I have not written much on this feature before, so at the behest of Engineer Li some pointers here. On higher-end vintage equipment (Preamps, Phonoamps and DACs) there are often a Phase Switch to cater to those who care (even obsess) over phase. To put it simply, many older recordings, be it classical or jazz or whatever, were recorded phase-inverted. My experience is that in a good system it makes a difference to have the choice, but if one listens to a mix of the modern and vintage (as I), switching back and forth is barely practical even if the switch is at one's finger tip. On the other hand, if one deals with a Preamp that is itself Phase-Inverted, like the Goliath Douk E6 (referenced above), or most CJs, it pays to have a means to invert phase (instead of switching speaker cable polarities, which is my preferred way). With this statement, if you infer that the Editor thinks Phase-Correctness is more important in a Preamp than in a Recording, you are damn right. I'd not belabor the point here. Suffice to say, this is a useful feature].
- Ground (New Feature) This is fascinating. According to Engineer Li, with the removal of the 300/600 ohm switch a new function is added. This is because the Center Tap (300 ohm) is now permanently grounded, circuit board repurposed to the dual channel XLR/RCA Switches, etc. It's kind of confusing on the back panel, but follow me: 1) No matter where the Switch Position, both XLR and RCA will work properly; 2) XLR, with its carefully grounded planes and differentiation of ground and -ve return, of course should be switched to XLR (unless your system is uniquely queer, and I hope not); 3) RCA is grounded when switched to RCA position, but floated when switched to XLR position! This is of great use to the minority of people who experience hum with trannies [Editor: sorry to say, imho these people have usually committed basic errors in setup; analog SUT users should be familiar with this].
- DC 5V Input This remains the Same as in previous v2. USE According to Engineer Li, the 5V is used to operate the Switches, and not in the circuit path. The 5V has to be plugged in for: 1) both XLR Input and Output needs the 5V connected; 2) Phase Reversal needs the 5V. In RCA only mode Mr Li said, and as I've experienced before, even when the 5V is not needed, the 5V still changes the sound. Even a casual generic cellphone 5V source will make the sound just a trifle warmer. But my system does not need extra warmth, so I'm not necessarily keen, YMMV. Engineer Li stresses that a proper LPS 5V supply (they have developed one which we hope to test one of these days) makes a significant difference. Let's say this remains on our agenda. Since the feature is here, we should try it out! 5V Source For reasons unknown, rarely a certain 5V cellphone charger may not work. If that is the case, just switch to another one.
- XLR/RCA Conversion Same This can be easily accomplished, but 5V is usually needed. IMHO, it's more than worth its price even if used just as a two-way XLR/RCA Converter. Very versatile tool.
Some photos taken recently👆
Ursula's Paddington, Sydney